Rendered at 16:18:18 GMT+0000 (Coordinated Universal Time) with Cloudflare Workers.
bestouff 2 hours ago [-]
I'm using the hardware tester from Treedix in which you have to plug both ends of the cable and which tests a lot of things, I'm quite fond of it.
I have a basket with a lot of USB-c cables and without the tester I can't remember (nor guess) which one does what.
traceroute66 15 minutes ago [-]
> I'm using the hardware tester from $INSERT_NAME_HERE
Oh god not again... before everyone starts naming their favourite brand, here's a 265 comment HN thread[1] (from last week !) on why these cheap USB-cable "testers" are not worth anything.
TL;DR You need a six-figure wallet to seriously call anything a "hardware tester" for USB cables. User ChrisMarshallNY has a one-liner summary buried in that thread:
Think about it. You need to generate a precise, calibrated, 40GHz signal, transmit it, then precisely measure the returned signal for phase, amplitude, and waveform integrity -at that speed. Oscilloscopes and logic analyzers that run at that speed, are damn expensive.
If you only paid $40 for a black-box on your favourite online marketplace, then what you've got is definitively NOT a USB-cable tester.
Huh? Decent quality cable testers can be had for like $20,000. There's a difference between a general-purpose oscilloscope or logic analyzer and a purpose-built domain-specific appliance. I probably could've saved up for one in just a few months back when I had a job earlier this year.
traceroute66 7 minutes ago [-]
> Decent quality cable testers can be had for like $20,000.
See the discusison linked to.
Trust me, my interest was piqued by that thread and I went down the rabbit warren with Mr Google and spent far too much time on the subject. I looked at the various manufacturers and the setups required.
TL;DR: To start with, you need fancy harness assemblies. Then you need to plug those harnesses into very, very expensive equipment.
You're not going to find anything for $20k. USB-cable testing can't be done the same way copper CAT6 certification can with a 20k Fluke.
For those who want to play with Mr Google, some manufacturers from my notes: Wilder Technologies, Allion, Keysight, Tektronix, Teledyne LeCroy
Yep, I probably have the same one. Insanely useful, and it is also crazy how much variance there is in cables. You can’t believe what the sellers claim, so many times they end up being less capable than claimed.
callumprentice 1 hours ago [-]
Would this tell me if a cable is close to the end of it's life? I like to travel light and I've had cables (mostly phone/pad power) go out on trips after working as expected when I packed.
cinntaile 1 hours ago [-]
I think you would need something that tracks relevant per cable metrics over time to see if it is degrading.
That one just says yes/no, but maybe yes/no starts to flicker around its end of life?
callumprentice 45 minutes ago [-]
Nod - that's what I was thinking. I expect it's often the connectors that deteriorate so perhaps moving them around while plugged in would tell me. Seems like a useful tool to have around.
blightful 2 hours ago [-]
Nice. You just got them a sale from me. I have a crap ton of cables so this will come in handy.
lxgr 1 hours ago [-]
Great utility.
The only wrinkles for me are that Macs apparently don't interrogate cables when they don't have to, i.e., when the power adapter supplies <= 60W (not sure if that's a USB-C protocol or an Apple implementation limitation) and that the website copy is full of GPT-isms, which makes me suspect that some of the output might be assumed instead of empirically validated as well.
robot_jesus 1 hours ago [-]
I'm curious if this also works for USB-A to USB-C. The use case: My Suburu has USB-A inputs and only allows wired Carplay. When I upgraded my iPhone and ditched Lightning, I had to try 6 different cables from my cable drawer to find one that supported data transfer.
I have so many cables I've accumulated over the years, I should either purge or at least categorize the functionality of each.
reasonabl_human 26 minutes ago [-]
I see other folks provided options, in case you want to avoid aliexpress, this one worked for me for the past 4 years
I came here to ask the same thing. I did find a Linux tool with the same name and purpose but that seems to be an entirely different codebase: https://github.com/nedrichards/whatcable-linux
I have a handful of wireless keyboards that just absolutely refuse to negotiate for charging with certain cables at all, so I'm hoping this will help me at least figure out what those keyboards are looking for in terms of cable.
2 hours ago [-]
pdpi 1 hours ago [-]
I literally spent more than an hour yesterday debugging issues with USB-C cables that I wasn't aware were charging only, and this shows up today... Better late than never, I suppose, and definitely worth my ten quid.
david422 22 minutes ago [-]
I was trying to figure out slow network speeds one day and I finally swapped an ethernet cable and got full speed.
It turns out some ethernet cables are missing wires - and capped at 100Mbps! Wait what? I didn't even know that was a thing. I don't know where I got the wire, but into the trash it goes.
lxgr 1 hours ago [-]
If you can afford it, I'd honestly throw these out. "Charging only" is not a spec-compliant thing in USB-C, and personally I wouldn't want to re-discover which devices do and don't support them every time I just want to quickly grab a cable.
What's less easy to replace are all these damn USB-C devices lacking the UFP-identifying circuitry that only work on USB-A chargers using A-to-C cables...
pdpi 51 minutes ago [-]
To be clear, they're not literally "charging only", AIUI they're spec-compliant cables with USB2.0 480Mbps and power delivery, and they're allowed to not have the four SuperSpeed wire pairs. They're still useful for low bandwidth devices (like charging my keyboard/mouse).
Incidentally — I spent an inordinate amount of time searching for USB3.2 cables on Amazon, and the vast majority of cables were actually just USB2.0 cables with PD support, and not actual Full-Featured cables.
lxgr 32 minutes ago [-]
Ah, I love these as they're generally much thinner/lighter/more flexible than USB-C 3 cables but still support at least 60W power delivery! Advertising them as USB 3 is a shame, though.
cortesoft 44 minutes ago [-]
I would recommend getting one of the small cable testers, like the one from Treedix. Gives you all sorts of information very quickly, including resistance levels and capabilities.
extinctLizard 1 hours ago [-]
Small question: did anybody succeed to pay via Apple Pay?
nerdsniper 28 minutes ago [-]
Something that keeps needing to be pointed out every thread this stuff appears on: What these tools report are not functionally different from just believing "what's on the packaging", despite the misleading marketing claims.
These tools read a chip called an "eMarker". These eMarkers are programmed to say whatever the manufacturer wants them to say - there's no requirement that the information be based in reality. Plenty of cables have eMarkers that claim "40Gbps" or whatever speeds, or support 240W PD...but absolutely cannot deliver either of those. And none of these consumer level software or hardware testers can actually test either of those claims. They can only take the cable's own claims at face value.
Resistance measurements can cursorily test claims of 240W but resistance changes with temperature which changes with current...so unless your tester puts 5 amps down the wire for 5 minutes and then tests resistance it's not a very good test. AFAIK none of the testers flow 5 amps through the cable.
Actual maximum data throughput is very hard to know. The only way to really "know" how much data can flow through a cable is with an expensive oscilloscope or cable tester. Because 80Gbps cables run at ~13GHz, at minimum you need a 26GHz scope (Nyquist–Shannon sampling theorem) or more practically a 52GHz scope. And it turns out it's really expensive to measure electrical signals 52 billion times per second. The necessary devices start at $15,000 (cable signal integrity tester) [0] on the very low end and only work for max 10Gbps USB 3.2 cables, or past $270,000 for 80Gbps USB4 cables (proper 60GHz oscilloscope) [1].
On the high end, each signal integrity test device can actually cost $1-2 million [2] where the base unit starts at $670,000 plus then spending additional money for hardware-accelerated analysis, specialized active probes, and the specific PAM-3 / USB4 compliance software packages.
I have a basket with a lot of USB-c cables and without the tester I can't remember (nor guess) which one does what.
Oh god not again... before everyone starts naming their favourite brand, here's a 265 comment HN thread[1] (from last week !) on why these cheap USB-cable "testers" are not worth anything.
TL;DR You need a six-figure wallet to seriously call anything a "hardware tester" for USB cables. User ChrisMarshallNY has a one-liner summary buried in that thread:
If you only paid $40 for a black-box on your favourite online marketplace, then what you've got is definitively NOT a USB-cable tester.[1] https://news.ycombinator.com/item?id=49152255
See the discusison linked to.
Trust me, my interest was piqued by that thread and I went down the rabbit warren with Mr Google and spent far too much time on the subject. I looked at the various manufacturers and the setups required.
TL;DR: To start with, you need fancy harness assemblies. Then you need to plug those harnesses into very, very expensive equipment.
You're not going to find anything for $20k. USB-cable testing can't be done the same way copper CAT6 certification can with a 20k Fluke.
For those who want to play with Mr Google, some manufacturers from my notes: Wilder Technologies, Allion, Keysight, Tektronix, Teledyne LeCroy
Here's one link from my researches: https://www.keysight.com/blogs/en/tech/bench/2023/02/17/powe...
The only wrinkles for me are that Macs apparently don't interrogate cables when they don't have to, i.e., when the power adapter supplies <= 60W (not sure if that's a USB-C protocol or an Apple implementation limitation) and that the website copy is full of GPT-isms, which makes me suspect that some of the output might be assumed instead of empirically validated as well.
I have so many cables I've accumulated over the years, I should either purge or at least categorize the functionality of each.
https://a.co/d/0d9EOGRW
Does require a bit of setup, can scan reviews to see if people have optimized a config for your specific vehicle
But it is the second product I tried; the first one didn't work (it's a 2020 Stellantis car). So, YMMV.
https://github.com/nedrichards/whatcable-linux
But (hazard guess) it comes with a headless CLI binary (no GUI libraries needed) so probably could be ported to Linux (easily with an LLM?)
https://github.com/darrylmorley/whatcable
As I understand it, Windows doesn't expose the necessary low-level hardware information for something like this to be possible.
I have a handful of wireless keyboards that just absolutely refuse to negotiate for charging with certain cables at all, so I'm hoping this will help me at least figure out what those keyboards are looking for in terms of cable.
It turns out some ethernet cables are missing wires - and capped at 100Mbps! Wait what? I didn't even know that was a thing. I don't know where I got the wire, but into the trash it goes.
What's less easy to replace are all these damn USB-C devices lacking the UFP-identifying circuitry that only work on USB-A chargers using A-to-C cables...
Incidentally — I spent an inordinate amount of time searching for USB3.2 cables on Amazon, and the vast majority of cables were actually just USB2.0 cables with PD support, and not actual Full-Featured cables.
These tools read a chip called an "eMarker". These eMarkers are programmed to say whatever the manufacturer wants them to say - there's no requirement that the information be based in reality. Plenty of cables have eMarkers that claim "40Gbps" or whatever speeds, or support 240W PD...but absolutely cannot deliver either of those. And none of these consumer level software or hardware testers can actually test either of those claims. They can only take the cable's own claims at face value.
Resistance measurements can cursorily test claims of 240W but resistance changes with temperature which changes with current...so unless your tester puts 5 amps down the wire for 5 minutes and then tests resistance it's not a very good test. AFAIK none of the testers flow 5 amps through the cable.
Actual maximum data throughput is very hard to know. The only way to really "know" how much data can flow through a cable is with an expensive oscilloscope or cable tester. Because 80Gbps cables run at ~13GHz, at minimum you need a 26GHz scope (Nyquist–Shannon sampling theorem) or more practically a 52GHz scope. And it turns out it's really expensive to measure electrical signals 52 billion times per second. The necessary devices start at $15,000 (cable signal integrity tester) [0] on the very low end and only work for max 10Gbps USB 3.2 cables, or past $270,000 for 80Gbps USB4 cables (proper 60GHz oscilloscope) [1].
On the high end, each signal integrity test device can actually cost $1-2 million [2] where the base unit starts at $670,000 plus then spending additional money for hardware-accelerated analysis, specialized active probes, and the specific PAM-3 / USB4 compliance software packages.
0: https://www.totalphase.com/products/advanced-cable-tester-v2...
1: https://www.edn.com/12-bit-oscilloscope-operates-up-to-65-gh...
2: https://www.eevblog.com/forum/testgear/uxr1104a-infiniium-ux...